Im going to the notorious heartbreaker dyno (Surrey rolling road) on thursday, to see if i'm fueling ok as barbz has fitted a 3.5" race cat to my car so potentially going to see more ponies if fueling is good, it certainly feels it on the road..or maybe its the weather?

whish me luck...lets se if i can crack 320hp on this "realistic" bad boy of a dyno!

Good luck mate.

Would pop down if it was any other Thursday, but im off to the Ace meet this week.

run is at 3.00pm might go to ace after!

Ah, I wouldnt of been able to make it anyway, I thought you were doing an eve run.
Yeah pop down to Ace....

what time you going.....conga?

Conga?

Try and leave Walton around 6-6.30pm latest.

well we could cruise up together shall i meet you in walton? my mate might come he is in sunbury.

Yeah that sounds good mate, the only way I know is M25 then north circular, but M25 at that time is awful, just thinking if you know any other routes, otherwise M25 it is.
Can meet anywhere in walton where there is some space for cars, then we can take off from there.
Maybe outside Zio Italian restaurant where the Plough pub used to be, or the road next to Homebase avoiding the car park as its always busy, around 6.15 pm?
Unless you want to go a different route or have any other ideas, I'm easy.

i know a few routes a316 or a40 or pump lane to target roundabout...all will prob be busy!

shall i meet you in the slip road as you go into homebase its straight on where the posh houses are?

Yeah, perfect mate. Around 6.15 then, that o.k?

yep, should be fine,ill let you know otherwise!

cool.

well, my heart is not broken..... power/torque

boost

fuel

Charlie says (meow) that the fueling is on the edge now what do people think?....leighton?

Maybe lower the boost a bit??

or get flea to mapp it again!!

What's your spec mate???

lower the boost ...are you mad

if flea thinks it needs it ill remap it.....but rather not spend another £300!

Im sure he wont charge you that much as it will probably be just a tweak not a full remap.
Ask him.

Full Spec is:

apexi filter and pro alloy sip
gt28rsr (0.6 bar actuator)
evo 8 fmic custom short pipework
h&s downpipe with 3.5" 100 cell cat and 2.5" cat back blueflame.
apexi avcr
walbro 255 with direct feed
fc performance map
helix organic clutch
forge re-circ valve (green spring)
crank case breather mod
barbz "tickled" manifold

I have std fpr, so if it needs a 3.8fpr it requires a full remap

i need to see were this extra 100hp is on yours....in gear drag experiment next time!

Yeah I know mate, had the odd chance but I wasnt that sure on the roads that I dont know in the areas we were in. Im sure there will be a chance sometime soon.

got to be careful now, the roads are getting slippy....right time and place an all!
need to lower my boost in first gear i think..still loads of wheel spin!

Slight overboost to 1.3 but is it set for 1.2, looks prety steady at 1.2, tails of to 1.1 at rpm limit. You could have gone higher than that surely, 1.4? But maybe not without extra cooling/aquamist. Are you running 95 RON?

Fueling at around 12 AFR does look a little high (ie: lean), with my wideband I see around 11 IIRC, and according to Flea it was mapped to mid 11's. With my R turbo, aquamist, 1.4 bar boost and 99 RON with 3.8 FPR(but otherwise similar spec) I'm a bit behind you, but not far (325). Of course if you really want to push boost, try 1.7 (where Flea got me 336 )

running on v-power

boost controller is set to 1.3bar but dosen't hold it. always starts tailing straight away.....i think this maybe to do with my actuator being 0.6bar but to be fair i don't want to push it to much further as im on std internals and 320lbft is probably enough!

my injectors are maxed out so 3.8bar reg is prob the next step?

thats a cracking result for that turbo, nice torque curve, good spool up, i would be well chuffed with that, congrats

cheers,
it feels lovely drive, just done donington and ran 1.1 bar and was perfect all day!
the torque and spool up are as good as they look on the road,the engine really is a peach like this.

Keep it down around there... some of us live on that road.

really? you still got a coop kenno?

I do. Just got her back. Poor girl needs a bit of TLC so I need to find some time to either get her MOT'd and tidied up, or I'll get the angle grinder out.

Get it back on the road Kenno, has yours still got an RSR or am I thinking of someone else?

Back in the day mate was selling his AX-GT, some kind of bolt had snapped so he decided to replace it before the people turned up, he took an angle grinder to it just as they parked up and walked up the drive, all they could see was my mate with sparks coming out from under the bonnet......they turned around and walked back down the drive.

Barbalicious is doing a few tweeks to mine, adjustable FPR, stronger actuator and hopefully turning my H&S dogpipe into a true 3".
I am trying to get it to hold 1.3bar boost better and give it enough fuel, might get it back on the heartbreaker to show everyone down the pub.